Green Energy

FEED WATER PUMP HYDRAULIC COUPLING _VIDEO

FEED WATER PUMP HYDRAULIC COUPLING

Eighty Percentage 80% of thermal power plants has boiler feed pump , that takes the water from the feedwater system ( from the DA) and provide this water to the boiler system , to generate steam which is responsible for rolling the Turbine,Therefore Generate Electricity.

Normally Feed water pumped to the boiler is pumped to the Boiler's Drum where at the top point of the boiler, so we have to provide big pump that can handle big pressure with great flow to the boiler.

That is happened by this huge pump ( Boiler Feed Pump ) , BFP is usually rotate with 5000 rpm ,150 barg and can provide about 300 T/H.

This big pump needs a prime mover with high electrical rating - Power Plants usually use Electrical Induction motor - to rotate this pump, the rating of this prime mover is usually about ( 5 MWatts , 6.6 KVolts , 1600 rpm ). It is very huge rating if you imagin , 5 MWatts can provide Electricity to a small town.

so , as you see in the picture ( left hand is the prime mover_motor) , (Right hand is the pump) and what is it at the middle of the picture??

Hydraulic Coupling

Hydraulic Coupling is used to transmit Power in a wear-free manner from a prime mover (driving machine) to a power consumer(driven machine-pump). the power is transmitted in the following way:-

* by means of a connecting coupling between the driving machine and geared variable speed coupling.

* by means of a step-up gear unit between the input shaft and primary shaft.

* hydro-dynamically by means of the working oil between the primary wheel and the secondary wheel.

* by means of connecting coupling between the driving machine and geared variable speed coupling.

the control at the hydraulic coupling is done by the scoop tube control, it provide infinitely variable adjustment of the driven machine's speed. the power from the driving machine is transmitted to the primary wheel to the working oil, the working oil is accelerated in the primary wheel, and the mechanical energy is converted into the energy of fluid flow. the secondary wheel picks up the flow energy and converts it into mechanical energy. this energy is transmitted to the driven machine.

Speed Control

the speed of the driven machine is infinitely variable. this is accomplished by varying the amount of oil in the coupling during operation with the aid of the adjustable scoope tube.

* Scoop tube advanced as far as possible into the scoop champer of the coupling (0% position):minimum oil ring , minimum speed.

* Scoop tube retracted as far as possible out of the scoop champer of the coupling (100% position): maximum oil ring, maximum output speed.

I attached a small Flash file for Voith Company (shows the movements of Hydro coupling ), AND TWO FILES FROM VOITH

http://www.mediafire.com/?7titf097za3zu0y
http://www.mediafire.com/?j579r5d15ej5q6d
http://www.mediafire.com/?7udd1a9pz1phoow

- Solar Powered Pump
What is a Solar Powered Pump? A solar powered pump is a motor pump which is operated by utilizing power produced by solar panel using sun light. The pumping system is capable to draw water from open well or bore well and pond or canal.This pump is very...

- Boiler (master Fuel Trip)
Steam Generator ( boiler ) is very important equipment at thermal power units , Boiler is the steam supply for the unit to rotate the turbine's rotor , hence produce electricity at Generator's stator. Boiler usually equipped with solar and Main...

- Deaerator ( Part 2 )
DEAERATOR ( PART 2 ) OPERATION PROCEDURES ** Pre-start checks and operations(1) Vent valve shall be wide open.(At low load start, it may be necessary to throttle valve slightly to increase the operating pressure, but vent valve not to be fully close...

- Can Your Boiler Feed Pump Handle A Deaerator Pressure Transient?
Can Your Boiler Feed Pump Handle a Deaerator Pressure Transient? “This is part of an article talking about the importance of DA and BFP positions at power plant “ In a typical steam power plant, the boiler feedwater (BFW) pump takes suction...

- Boiler Control Theory (feed Water Control)
Boiler Control Theory (Feed water Control) The feed water is controlled to keep the drum level . Water-level controls continuously monitor the level of water in a steam boiler in order to control the flow of feed water into the boiler and to protect...

Green Energy